Subscribe to a magazine

Off-Road Hardware - New Products - July 2010

Portable Mig Welding System
Kevin Blumer | Writer
Posted July 1, 2010

Off-Road Hardware

K&N High-Flow Intake System for the Silverado/Sierra 1500
The K&N High-Flow intake system for the 2009-to-2010 Silverado/Sierra 1500 fits the 4.8L, 5.3L, 6.0L, and 6.2L engines and increases horsepower by 16.59 at 5342 rpm compared to stock output. The K&N High-Flow intake replaces the entire stock air intake system and is covered by K&N's million-mile warranty.
• Powder-coated heat shield protects the filter from engine heat
• Roto-molded polyethylene intake tube is shaped to achieve a more laminar airflow into the engine
For more information, contact:
K&N Engineering, Inc.
(800) 858-3333
www.knfilters.com

Skyjacker 4- and 6-Inch Lift System for 2009-2010 Ram 1500
Skyjacker has responded to the latest generation of Ram 1500 trucks by releasing a new suspension lift system available in 4- and 6-inch lift heights.
• Maintains factory steering geometry
• Includes CNC-machined steering knuckles, front and rear crossmembers, one-piece differential skid plate, four-link relocation brackets, and replacement variable-rate Softride rear coil springs
For more information, contact:
Skyjacker Suspensions
(866) 4-A-Dealer
www.skyjacker.com

Bushwacker Cut-Out Fender Flares for the Tacoma
If you need extra tire coverage and a larger fender opening and don't want to use fiberglass fender and bedsides, Bushwacker's Cut-Out fender flares are the way to go.
• Gain three inches of side coverage and a one-inch larger fender opening on '95-to-'04 Toyota Tacomas
• Dura-Flex material is UV-protected and carries a lifetime warranty against fading, chalking, and cracking
For more information, contact:
Bushwacker
(800) 234-8920
www.bushwacker.com

Traxxas
4 Wheel Parts Slash RC Truck

Traxxas has added the 4 Wheel Parts/Greg Adler model Slash RC truck to its lineup. Modeled after the real Pro-2 class truck, this truck can hit speeds up to 40 mph.
• Waterproof electronic speed control
• Complete with seven-cell battery pack, controller, and battery charger
For more information, contact:
4 Wheel Parts Wholesalers
(800) 775-7584
www.4wheelparts.com

Photos

View Photo Gallery

Swapping Solutions from Inchworm Gear
If you're swapping driveshafts and transfer cases in your Toyota, Inchworm has a speed sensor adapter and a collection of driveshaft flange adapters that will let you seamlessly tailor your Toy to fit your needs.
• Speed sensor adapters allow older transfer gear driven transfer cases to be swapped into newer Toyota trucks that require a speed sensor signal from the transfer case
• Driveshaft flange adapters let you bolt together different combinations of output flanges and driveshafts that would not otherwise be possible without custom driveshaft mods
For more information, contact:
Inchworm Gear
(530) 677-8111
www.inchwormgear.com

Photos

View Photo Gallery

Trail Welding Hits a New Level
Hobart introduces the Trek 180, a portable MIG welding system inspired by and designed for off-road enthusiasts and fabricators. This revolutionary trail welder operates off its self-contained battery or 115V power and travels where other portable or fixed units can't. The Trek welds 24-gauge up to 1/4-inch mild steel in a single pass and recharges off an automotive power inverter or 115V receptacle.
• 52-pound package operates while plugged in or completely cordless
• 180 amps on 115V power (an output previously limited to 230V welders), 120 amps on 17VDC battery power at 20-percent duty cycle, is ideal for fabrication in the garage or repairs off-road
• You can also recharge the unit inside a vehicle using an automotive power inverter
• No more need to run you welder off heavy-duty alternators or to carry a second battery.
For more information, contact:
Hobart Welders
(877) 462-2781
www.hobartwelders.com

Photos

View Photo Gallery
Load More Read Full Article

Comments

Advertisement