• JP Magazine
  • Dirt Sports + Off-Road
  • 4-Wheel & Off-Road
  • Four Wheeler
  • Get A Print Subscription
  • Get A Digital Subscription
  • Gift Subscriptions
  • Subscriber Services
  • Back Issues
  • Personalized Covers

jeep Cj3a Body Swap - rear - Photo 27903634

Back to Article
Share this
  • We added a rear crossmember to the lopped-off M38A1 frame. The beat-up old gas can is actually the fuel tank. It's held in place with a gas-can mount stolen from Hazel's M-715. The strap steel that keeps the can in the mount is some rusty shipping strap that we found in the fields while walking the dog. A scrap sheet of aluminum bent in a buddy's brake along with some angle iron and a few rivets cover the axlehousing that was poking into the bed.
We added a rear crossmember to the lopped-off M38A1 frame. The beat-up old gas can is actually the fuel tank. It's held in place with a gas-can mount stolen from Hazel's M-715. The strap steel that keeps the can in the mount is some rusty shipping strap that we found in the fields while walking the dog. A scrap sheet of aluminum bent in a buddy's brake along with some angle iron and a few rivets cover the axlehousing that was poking into the bed.
154 1003 01+jeep cj3a body swap+grille Our MB grille already had the shroud removed. We welded together some strap steel and angle iron to create a bracket that would bolt to the grille and to our mystery Dodge radiator that came from Hazel's Willys truck. We needed to switch to a smaller 15-inch, vintage-looking mechanical fan (PN 9101515) from Speedway Motors to clear everything. With the $100 CJ-3A tub in place, we went to work on the freebie Willy's truck seats. We chopped 8 inches out of the backrests and threw away the rat-nested padding and rusty springs. Then we switched 'em (driver seat on the passenger side, passenger seat on the driver side) so we could still access the factory toolbox underneath. We covered the seats with 3/8-inch plywood and a Mexican blanket for padding. You'll notice we also had to cut a hole in the bed of the tub for axle clearance. Hazel's Willys truck steering assembly found a home in Sloppy Seconds after we chopped 4 inches out of the column and bolted it to the body with a reader-supplied CJ-2A column bracket. The box is bolted to the frame using the original Willys truck brackets, some 3/4-inch plate steel, and a pair of Grade 8 bolts. The pitman arm is a modified Willys truck part, the draglink is a lengthened early CJ part, and the stubby open exhaust is made from all leftover remnants. We wanted to hide a lot of things on the Jeep to keep the overall look uncluttered and, well, to get people scratching their heads wondering if our Jeep actually ran and drove. We built a tray and hid our Yellow Top Optima battery inside the rear wheelwell tub. We didn't have to mount it sideways, but Optima batteries are no-spill and can be mounted on their side if need be. We added a rear crossmember to the lopped-off M38A1 frame. The beat-up old gas can is actually the fuel tank. It's held in place with a gas-can mount stolen from Hazel's M-715. The strap steel that keeps the can in the mount is some rusty shipping strap that we found in the fields while walking the dog. A scrap sheet of aluminum bent in a buddy's brake along with some angle iron and a few rivets cover the axlehousing that was poking into the bed. We couldn't stand spending nearly half the Sloppy Seconds budget on a windshield frame and glass that we were only going to chop up. So we built a windshield frame out of 1-inch copper pipe and some Lexan. We sweated most of the frame together. We then used an angle grinder to cut a notch around the inside perimeter of the pipe for the Lexan to slide into. The top of the frame was glued together with silicone to avoid melting the Lexan. Is it street legal? Don't ask. But we think the copper sure looks cool.
Back to Article
< 1 - 9 of >

Related Galleries

Connect With Us

Newsletter Sign Up

Subscribe to the Magazine

Sponsored Links