Spring-time again for another weeklong wheeling adventure. For the last six years, a group of Nissan 4x4 enthusiasts have held a gathering to tackle some trails, do some camping, and share in camaraderie. So when Andy Schauer contacted us last March, wanting to know if we'd like to attend Arizona Run VI, we said sure thing.

Lurking about the rolling slabs of rock in Moab, Utah, we found Jeff Graham’s Bronco clawing through crevices and bounding up steep inclines with the elegance of a mountain lion—well, not quite. The impressive display of capability, however, reminded us how bulletproof ’78-’79 Broncos are right off the factory floor. By performing some simple mods, Jeff has turned an already competent truck into something downright burly.

Jeff, of Farmington, New Mexico, bought the ’79 Bronco from the parents of former owner Chris Hull after Chris who died in 1993. Chris, who was Jeff’s best friend, had just started fixing up the truck, so Jeff and his wife decided to finish the buildup in his memory. With the help of Jeff’s brother-in-law Ron Woods, the beefing began.

The Bronco was in rough shape with about six different colors adorning the sheetmetal, and it sported 33-inch street meats. Chris had almost finished the interior, so Jeff first concentrated on the body, which he had massaged and painted Victory Red by Fidel Lobato at Valley Auto Body.

The 33-inch tires were replaced by 35x12.50-15 BFGoodrich Mud-Terrains, which came courtesy of a Rancho 3 ½-inch coil-spring lift up front and 3½-inch leaf springs in the rear. Some fender trimming was also necessary to clear the larger meats. The tires are mounted on 15x10-inch Alcoa wheels. He also replaced the shocks with Rancho RS5000s and a steering stabilizer to steady the ride.

What makes these Broncos so capable right out of the box is the beefy hardware supplied: A reverse-cut Dana 44 up front and a 9-inch rear, which are linked to a NP205 transfer case and a T-18 transmission, make for an impressive lineup for a factory ½-ton. They also sport coil-spring front suspensions, which most people prefer because these suspensions offer very good axle-control and allow you to build awesome wheel travel into them.

The drivetrain components are well-known for their durability. The T-18 and the NP205 have been used for many years in a variety of 4x4s. They are respected for their sturdy construction, low gearing and low failure rate. The axler on the 9-inches (later models, such as those in the ’78-’79 trucks) and Dana 44s have larger diameters than most ½-ton stock axles. The larger ring-gear diameter also adds to the stronger construction. While owners of other stock vehicles spend countless dollars swapping these exact parts into their trucks, owners of ’78-’79 Broncos are ready to go with the stock trim.

Jeff, however, still found room for modification. Realizing that the stock 3.50:1 gearsets that came in the Bronco were inadequate for the 35-inch tires, he swapped 4.56s in both ends. The open differentials were tossed in favor of Lock-Right lockers at both ends. New Warn hubs round out the axle upgrades. Jeff’s Bronco is an excellent example of turning a good stocker into a great ’wheeler with just a handful of upgrades.

Project Baja Bomber - Part 1
Project Baja Bomber - Part 2
Project Baja Bomber - Part 3
Project Baja Bomber - Part 4
Project Baja Bomber - Part 5
Project Baja Bomber - Part 6

Shocking but true: There hasn't been a Ford Super Duty on the cover of Four Wheeler for almost two years. Well, it's high time we changed that Super Duty drought by presenting Ron and Christine Williams' stunning '00 Crew Cab shortbox.We met the Williamses at the Summer 4-Wheel Jamboree in Bloomsburg, Pennsylvania. We were impressed by the clean look of their massive Super Duty, but as we talked with them we became even more impressed as we learned that Ron did all of the project planning and almost all of the wrenching on the truck himself (with some help from friends including Barry Miller and Tony Lacy). All while he was overseeing his busy bathroom remodeling business.

Project Fiery Redhead - Part 1
Project Fiery Redhead - Part 2
Project Fiery Redhead - Part 3
Project Fiery Redhead - Part 4
Project Fiery Redhead - Part 5
Project Fiery Redhead - Part 6
Project Fiery Redhead - Part 7
Project Fiery Redhead - Part 8
Project Fiery Redhead - Part 9
Project Fiery Redhead - Part 10

Considering the state's affinity for full-size trucks, Dodge appropriately chose the Texas State Fair to unveil the titan (no pun intended) of its truck lineup. The Ram Mega Cab Dually adds an extra pair of rear wheels and tires to the rear axle for a staggering 6' 4" total rear track width. The dually configuration is available exclusively in the 3500-series and only with the Cummins turbo diesel, with the choice of a four-speed automatic or six-speed manual transmission. A limited-slip differential is optional.