Rock Ram Hydraulic Steering System Install 1969 Ford Bronco

Rock Ram Hydraulic Steering Quick Steering

Is your steering what you want it to be? For most of us, the answer would be, "no, it isn't." Running big tires and hitting the trails can really tax a stock steering system, and make turning the steering wheel into an ordeal that only a bodybuilder can manage. Even our friend who runs 38-inch tires on his Super Duty but never hits the trail has a hard time turning his big tires when going slowly. This also was the situation with our Bronco. Wanting to improve this sub-par steering, we searched for a product that could make turning the wheel an easy affair.

The solution to our steering woes came in the form of the AGR Rock Ram. Basically a hydraulic assist, the Rock Ram mounts from the axlehousing to the tie rod and exerts force on it. This takes a great deal of load off the steering box itself and makes turning the wheel easy.

Rock Ram Hydraulic Steering Arg Rock Ram Kit

This is what you get when the AGR Rock Ram kit arrives: new Rock Ram gearbox tapped with fittings for the ram, a Super pump, the Rock Ram cylinder, hoses, rod ends, and mounting tabs.

This is what you get when the AGR Rock Ram kit arrives: new Rock Ram gearbox tapped with f

To graft our Rock Ram into position on our '69 Bronco we headed down to Off Road Unlimited in Burbank, California. While the installation was a bit of a challenge, the result was well worth it. In its prior form, we couldn't even manage to turn our poor Bronco's big front tires when parked on pavement. After installing the Rock Ram it felt like we had shod the Bronco with the tires from a compact car, as steering was effortless. The only quirk we noticed is the Rock Ram system made our steering a bit quicker. This made our steed a bit twitchy until we adapted by slowing down our steering inputs. A nice and unexpected side effect was that our Bronco no longer jerks around while shifting due to the rear Detroit Locker locking and unlocking. So if you want to be able to steer your 4x4 on the street or trail without having to hit the gym, a Rock Ram might be for you.

1. Our Bronco was already equipped with an AGR power-steering pump and box when it was outfitted with power steering using a James Duff Saginaw Power Steering conversion kit; so we just had to replace the old box. You can see where the new AGR box has been tapped with fittings for the hoses that go to the Rock Ram.
1. Our Bronco was already equipped with an AGR power-steering pump and box when it was out
2. The next step was to cycle the suspension of the Bronco to try to figure out where the Rock Ram would actually fit. Very little room was available for us to play with because the track bar mounts to the front of the axle on early Broncos right where the Rock Ram needs to be. The massive tie rod that Performance Unlimited built for us also took up a bit of space.
2. The next step was to cycle the suspension of the Bronco to try to figure out where the
3. After a bunch of head-scratching, a few mock setups, and lots more suspension cycling, we finally decided on a plan of attack. To make room for the Rock Ram we needed to move the track bar up and out of the way, so a new lower mount was built. It is seen here in its early stages of development. Eventually it would be fully welded and the front bolt removed.
3. After a bunch of head-scratching, a few mock setups, and lots more suspension cycling,

4. To raise the other end of the track bar, we simply torched the track bar drop bracket out of the way and put the track bar into the stock mount. By using the new lower mount fabbed onto the axle and the stock upper mount, we were able to raise the track bar three inches-making just enough room for the Rock Ram.
4. To raise the other end of the track bar, we simply torched the track bar drop bracket o
5. After moving the track bar, we then had to switch from a dropped pitman arm back to the stock unit with no drop in order to keep the drag link and track bar at the same angle. Doing this eliminates bumpsteer.
5. After moving the track bar, we then had to switch from a dropped pitman arm back to the
6. After centering the Rock Ram in its stroke, we figured out where it needed to be on the tie rod with the wheels pointed straight. We then mocked up the setup and worked the ram and the steering through their respective cycles to make sure there was enough clearance. After a few minor adjustments we were able to finalize the welds.
6. After centering the Rock Ram in its stroke, we figured out where it needed to be on the

7. Ideally, we would mount the other side of the Rock Ram to the axlehousing, but we had to settle for the diff cover to keep the tie rod from hitting the ram when it went through its cycle. In the future we plan to upgrade to the thickest cover we can find so we don't have to worry about tearing the cover apart.
7. Ideally, we would mount the other side of the Rock Ram to the axlehousing, but we had t
8. With the Rock Ram in place, we went about centering the axle and putting the track bar back into position.
8. With the Rock Ram in place, we went about centering the axle and putting the track bar
9. The last step was to attach the hoses to the Rock Ram and bleed the power steering system.
9. The last step was to attach the hoses to the Rock Ram and bleed the power steering syst

Rock Ram Hydraulic Steering Clearance Shot

10. From this shot on the passenger side you can see that though there isn't much room, everything clears except for the bumpstop, which will be moved back a bit. Part of the minor tweaks we had to perform when cycling the suspension included moving the track bar to the back of the new lower mount, and also flipping the track bar so that its bend was pointing backward. You'll also notice where the C bushing mount was ground down for clearance.

Rock Ram Hydraulic Steering Finished Front End

11. Here you can see how nicely the Rock Ram tucks out of the way-part of the reason for all our effort. It would have been much easier to mount it below the tie rod, but having a hydraulic ram be the lowest point on your vehicle is not a good idea. If you have a leaf-sprung vehicle, or a rig with a track bar that mounts to the top of the axle rather than the front, your installation will be much easier than ours was.

SOURCES
James Duff Enterprises Inc. 261340 Highway 101 Sequim WA 98382 www.jamesduff.com	Off Road Unlimited www.offroadunlimited.com
AGR Performance Steering 4920 Rondo Dr Fort Worth TX 76106 www.agrperformance.com	Performance Unlimited 766 Grand Ave Hartford WI 53027 www.performanceunlimited.com