• JP Magazine
  • Dirt Sports + Off-Road
  • 4-Wheel & Off-Road
  • Four Wheeler
  • Get A Print Subscription
  • Get A Digital Subscription
  • Gift Subscriptions
  • Subscriber Services
  • Back Issues
  • Personalized Covers

131 0410 Sky 08 Z - Photo 8809691

Back to Article
Share this
  • The Z-Link suspension is not like a conventional four-link. With this kit the lower link arms bolt to Skyjacker frame brackets behind the axle, and the upper links pivot from the stock leaf-spring hangers in front of the axle to form the "Z" configuration. To secure all four links to the axle, Skyjacker developed these bolt-on mounts that sandwich the Dana 60.
The Z-Link suspension is not like a conventional four-link. With this kit the lower link arms bolt to Skyjacker frame brackets behind the axle, and the upper links pivot from the stock leaf-spring hangers in front of the axle to form the "Z" configuration. To secure all four links to the axle, Skyjacker developed these bolt-on mounts that sandwich the Dana 60.
131 0410 sky 01 z 131 0410 sky 01 z 131 0410 sky 02 z The first step for installing the 8-inch Z-link suspension (clears 38-inch tires) is to lay out all the parts and read the directions--even if you're a veteran racetruck builder like Curt LeDuc. Familiarizing yourself with the parts and instructions makes your wrenching go smoother and ensures better results. LeDuc's team tore into our Super Duty by stripping the old suspension and front axle from the truck. The frame was then cleaned and repainted to give the Skyjacker parts a proper home. We're blessed by having a rust-free California truck, so components like the old pitman arm came off and the new Skyjacker piece went on without any fuss. The lower Z-link arms mount to these bolt-on brackets in front of the transmission crossmember. Skyjacker designed these parts to use holes that come in the Ford frame from the factory so you only have to drill a couple of new ones per side. Make sure to use thread lock on all fasteners. Todd LeDuc took charge of installing the lower links into the new brackets on our truck. All four links are nonadjustable so he didn't have to worry about getting them set up to a specific length to locate the axle. The Skyjacker upper shock mounts are massive, which they need to be to support the weight of the truck. To help spread that load over the frame, the Skyjacker kit uses a backing plate that gets bolted into the framerail with the shock mount. The Z-Link suspension is not like a conventional four-link. With this kit the lower link arms bolt to Skyjacker frame brackets behind the axle, and the upper links pivot from the stock leaf-spring hangers in front of the axle to form the "Z" configuration. To secure all four links to the axle, Skyjacker developed these bolt-on mounts that sandwich the Dana 60.
To cope with the new steering angles caused by the added lift height, Skyjacker lowers the upper track-bar mount on the frame and raises the axle mount. You could reuse the stock Super Duty track bar with the Z-link kit, but we wouldn't. We highly recommend Skyjacker's optional heavy-duty track-bar upgrade because it's the only thing keeping the axle square in the chassis. <b>Ride & Drive</b><br>With the Skyjacker Z-link installed, our F-250 definitely rode better than it ever did with leaf springs. And there's very little vehicle roll even without the front sway bar installed. The Z-link kit gives the truck a better approach angle, but it does lose ground clearance at the lower arms when compared to the leaf springs. <br>To dial our truck in, we need to adjust the ride height to get more suspension travel up front. Right now the shocks bottom easily as there is only 3 1/2 inches of uptravel. It would be nice if Skyjacker offered a remote-reservoir shock that would give the suspension more travel with the same overall shock length. <b>35-Spline Upgrade</b><br>Want stronger 35-spline stub shafts for your Super Duty? Off Road Unlimited has developed a conversion kit that gives you 1 1/2-inch-diameter outers and a set of modified unit-bearing hubs to replace the stock 30-spline stuff. This kit works with the common Warn 35-spline locking hubs and is an easy bolt-on. By the time you read this, ORU should also have a live spindle conversion that will convert your Super Duty to conventional spindles and 35-spline outers. 131 0410 sky 11 z
Back to Article
< 1 - 9 of >

Related Galleries

Connect With Us

Newsletter Sign Up

Subscribe to the Magazine

Sponsored Links